Photon Brothers - Labor & Material Generator

0. Load Report Data

Select a property OR upload a PDF report (Roofr/IMGING)

📄 Click to upload or drag & drop PDF

Supports Roofr & IMGING Facet Detail Reports

Or manually edit measurements below

1. Roof Measurements

From Roofr or IMGING report (auto-filled if you loaded a property above)

Total Roof Area (sqft):

Roof Pitch (X/12):

Ridge + Hip Length (lin. ft.):

Valley Length (lin. ft.):

Eaves Length (lin. ft.):

Rakes Length (lin. ft.):

Facet Count:

ℹ️ Pitch Note: If pitch varies across facets, use predominant pitch. Adders apply only if ≥8/12.

2. Roof Complexity Factors

Select conditions that apply to this roof

Penetrations & Obstacles

Number of Chimneys:

Number of Skylights:

New Vents to Install/Cut:

Decking Sheets to Replace:

Replace Existing Ridge Vent (materials only)

Install New Ridge Vent (materials + $3/lin. ft.)

Pipe Flashings & Vents

4-N-1 Pipe Flashings:

TRI-BUILT 750 Vents:

Kitchen Pro Vents (6–8" ducting):

Bath Pro Vents (3–4" ducting):

6" Pitched Roof Jacks:

Story & Access

Two-Story House

Three-Story House

No Trailer Access (debris offload)

Long Distance Charge (see map)

Difficult Access (remote/restricted)

Gutters

Install New Gutters

3. Pricing & Waste Factor

Base Price per Square:

Material Waste Factor (%):

Customer Price per Square:

📋 Roofr Recommended Waste Ranges:

10%: Simple roofs, closed valley system, minimal obstacles
12%: Typical residential roofs (standard complexity)
15%: Complex roofs, multiple valleys, several obstacles
17–20%: Very complex (many facets, high pitch, extensive penetrations)
22%+: Extremely complex or custom layouts

Adjust based on facet count, valleys, obstacles, and roof pitch from your Roofr/IMGING report.

Quote Summary

Total Roof Area: —

Base Cost (area × rate): —

Labor Adders: —

TOTAL QUOTE —

Labor Cost Breakdown (Adders)

Adder	Rate	Qty	Total	Status

Profitability

Customer Price

—

Total Job Cost

—

Labor + Materials

Gross Profit

—

Profit Margin

—

Goal: 30%

Adjust Target Margin:

%

→ Required price per square: —

Material Order

Based on GAF Timberline standards. Adjust for other brands.

Shingles

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
GAF Timberline HDZ (or equiv.)	32.80 sf / bundle	—	—	$51.33	—

Underlayment & Protection

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
GAF FeltBuster Synthetic Underlayment	1,000 sf / roll	—	—	$170.94	—
TRI-BUILT TMG Granular Ice & Water Shield (eaves/valleys)	~200 sf / roll	—	—	$96.24	—
GAF Pro-Start Starter Strip	120.33 lin. ft. / bundle	—	—	$94.62	—

Drip Edge & Trim

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
Highline Metals 28 Ga. — Eaves	10 lin. ft. / piece	—	—	$14.83	—
Highline Metals 28 Ga. — Rakes	10 lin. ft. / piece	—	—	$10.10	—

Gutters

Product	Per Unit	Qty	Details	Unit Cost	Total Cost
Seamless Gutters	Seamless / custom run	—	—	—	—

Fasteners & Accessories

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
TRI-BUILT Coil Roofing Nails	15 sq / carton	—	—	$73.62	—
TRI-BUILT Plastic Cap Nails	30 sq / pail	—	—	$15.53	—
TRI-BUILT High Performance Sealant	3 per job	3	—	$10.35	—
TRI-BUILT Roof Accessory Paint	3 per job	3	—	$10.42	—

Pipe Flashings & Vents

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
TRI-BUILT 4-N-1 Pipe Flashing	Each	—	—	$12.63	—
TRI-BUILT 750-S Galvanized Vent	Each	—	—	$24.50	—
TRI-BUILT Kitchen PRO™ Vent (6–8" ducting)	Each	—	—	$54.05	—
TRI-BUILT Bath PRO™ Vent (3–4" ducting)	Each	—	—	$29.08	—
Roof Jack Galvanized 6" Pitch	Each	—	—	$39.87	—

Ventilation

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
GAF Cobra Snow Country 4" Ridge Vent	4 lin. ft. / piece	—	—	$32.45	—

Ridge & Hip Caps

Product	Per Unit	Qty	Total Coverage	Unit Cost	Total Cost
GAF Seal-A-Ridge Hip & Ridge Cap	25 lin. ft. / bundle	—	—	$97.09	—

Estimated Material Subtotal —

Pre-tax. Gutters priced separately by installer. ⚠️ QXO prices valid through May 31, 2026 — update after June 1.

⚠️ Notes:

These are estimates. Always verify with exact product specs.
Waste factors applied to all quantities.
Material Roof Loading (supplier responsibility) not included unless noted.
Adjust brands/grades as needed for customer preference.

⚡ LABOR & MATERIAL GENERATOR

0. Load Report Data

1. Roof Measurements

2. Roof Complexity Factors

Penetrations & Obstacles

Story & Access

Gutters

3. Pricing & Waste Factor

Quote Summary

Labor Cost Breakdown (Adders)

Profitability

Material Order

Shingles

Underlayment & Protection

Drip Edge & Trim

Gutters

Fasteners & Accessories

Pipe Flashings & Vents

Ventilation

Ridge & Hip Caps